Bill's 200 20v for sale

[audios]

That could be, Ill ask Casey how he oriented them when installing. Here is the catch can/ccv set up. Although now I have the two lines going to BMW oil air separator's

I was told my my friend Ivan that i should not be venting out of the VC but only the block and he suggested doing what he on his 4ktq 20v where he had the return to the oil pan above the oil level. im still waiting on pics of his set up....

Sent from my iPhone using Tapatalk

[audios]

Pulled the piston rings today, seems to be some buildup behind the oil ring, does this look normal? Also the oil ring seems to be smaller in diameter than the middle and talk ring. Normally the VW/Audi oil rings work great and I do not change them, but think I may change these over


Sent from my iPhone using Tapatalk

[audios]

Pulled the rest of the Pistons and rods tonight, cylinder walls on three and five look scored.




Sent from my iPhone using Tapatalk

[audios]

Pulled the rest of the Pistons and rods tonight, cylinder walls on three and five look scored.




Sent from my iPhone using Tapatalk

[audios]

Found that the top ring was broken in cylinder number four. Looking to purchase rod bearings and the ultimate crankcase breather vent adapter from Marc at EFI express


Sent from my iPhone using Tapatalk

[PRY4SNO]

How deep is the scoring? Tough to tell but looks like it should hone out without requiring a full rebore?

[audios]

Found that the top ring was broken in cylinder number four. Looking to purchase rod bearings and the ultimate crankcase breather vent adapter from Marc at EFI express


Sent from my iPhone using Tapatalk

[WOMBAT]

The poor leak down is making a lot of sense... Glad you're making her new and proper.

[audios]

Soaking the pistons in seafoam to clean them up, seems to be working well


Sent from my iPhone using Tapatalk

[audios]

There is definitely some build up in the ring-lands, especially the oil ring. the severity seems to correspond to the leak down #'s. dosent want to clean up with the nylon brushes, will have to look up best way to clean w/o damaging pistons

[dana]

Bill, I have a piston ring groove cleaning tool, works pretty well. Looks like this.

[audios]

been doing a bit of reading, what do you all think of this :

http://www.angelfire.com/biz/snwvlly/bikes/dnthone.htm

Basically saying that you dont need to break the glaze or hone for the new rings...... just trying to make the best decision possible

[audios]

Gave a shot at ball honing tonight. Used A flex hone 240 grit , my first time. Hatching pattern is not perfect, but more alarming is these two scratches on cylinder three and five…


Sent from my iPhone using Tapatalk

[audifreakjim]

Can you catch your fingernail on those? I mean, they are going to effect compression and leak down, but hard to say how much. Looks like some rings were not de-burred during the gapping process.

[audios]

Not sure, I did not assemble motor, I figured it would effect a bit. I plan to just run it and build good breather.


Sent from my iPhone using Tapatalk

[audios]

Out of the garage at the farm, getting ready to make the voyage to my house


Sent from my iPhone using Tapatalk

[Afterthought]

I never did figure out for myself the exact proper way to set up an aftermarket catch can ...
do you have a source of vacuum pulling through it to the intake ?

My car project isn’t running yet , At the advice of some others I have set mine up to collect everything and I will drain it myself rather than running it directly to the pan .
Some were finding some pretty weird milky substance in there that they didn’t want ending up in the pan so I figured I would run it for a bit and see . Maybe someone more experienced on here has some advice.
A pic for reference from quattroworld URS4 FAQ

[PRY4SNO]

That milky substance should be an emulsion of water vapour in the oil.

[audios]

Just got back with the new van, snow on the white car



Sent from my iPhone using Tapatalk

[audios]

Installed piston rings tonight, also looked at the oil pick up tube. Found a lot of little plastic pieces. There were quite a few more than even in this picture…


Sent from my iPhone using Tapatalk

[Aktapod]

Those plastic pieces are pretty common. I'd bet they're the remains of the cam splash shield that sat under the oil fill cap. They pretty much all disintegrate eventually and end up in the sump.

Great work on the car! Jealous of the snow too

[audios]

Put on the new rod bearings tonight, took a few photos of the rod/ cap of cylinders 1&2 although they all looked similar. Any ideas of the possible cause of the markings?



Sent from my iPhone using Tapatalk

[audios]

Started on my take of a windage tray, based on Ian's (slacker20vt on MG)
http://www.motorgeek.com/viewtopic.php?t=23462



Sent from my iPhone using Tapatalk

[audios]

A bit more progress


Sent from my iPhone using Tapatalk

[audios]

Still not done, but bolted up....


Sent from my iPhone using Tapatalk