90q IMSA GTO (wanna-be) build

[DFrosty]

^^Looks very good! where does the bottom line on the expansion tank go/come from?

Thanks. The hose that goes into the back of the Rad...on the fan side?[/quote


My bad I worded that wrong, I was referring to the lower hose on the expansion tank, I see the top hose comes from the rad, where does the bottom one come from

No worries man. The only other hose attached to the expansion tank is at the bottom of it with a check valve and that hose runs down along the strut tower/inner wing, and does a switch-back around the motor mount and connects to the port at bottom right corner of Rad under the fan. This the one you mean?

Attachment ( 39476 ) : 90q_expansion tank hose_no fan.JPG


Attachment ( 39477 ) : 90q_expansion tank hose_with fan.JPG


Attachment ( 39478 ) : Screen Shot 2014-03-28 at 7.47.22 AM.png

[TopherGrace]

D'Frosty!!!!!

Thanks for the pictures sir, I am putting an engine where it doesn't belong so to speak and was hoping that the expansion tank upper and lower could be tied to the radiator

Thanks. The hose that goes into the back of the Rad...on the fan side?[/quote


My bad I worded that wrong, I was referring to the lower hose on the expansion tank, I see the top hose comes from the rad, where does the bottom one come from

No worries man. The only other hose attached to the expansion tank is at the bottom of it with a check valve and that hose runs down along the strut tower/inner wing, and does a switch-back around the motor mount and connects to the port at bottom right corner of Rad under the fan. This the one you mean?

[Twintowers]

Fire that thing up!

[PRY4SNO]

Updates?

[DFrosty]

Updates?

Thanks for asking dood. Unfortunately, only an update of the ugly kind...

The car was up on the dyno ready to be properly broken in and tuned :woowoo: !!

But...and a big but it is. During the warm up cycle, a sound of something breaking loose inside the motor was heard and promptly shutdown. The #2 cylinder rod bearing gave way due to oil starvation and after a bit of investigation, turns out that the machine shop that did the rebuild on the block installed all of the main bearings backwards :dur:

The machine shop has since completed all of the rebuild work part deux, the engine and gearbox have been reinstalled and now awaiting a new oil pan extension after the original, plus the replacement, have perplexingly broke at the exact same spot during installation.

I should rename my file for this project to 'Project Setback'

[PRY4SNO]

What a bummer! But, you're getting ever closer... when do you estimate being on the road again, ripping up pavement?

[DFrosty]

What a bummer! But, you're getting ever closer... when do you estimate being on the road again, ripping up pavement?

Indeed. As of now, the plan was to have her back up on the dyno by end of this month...which is this week. If the 2nd replacement pan extension breaks again, we'll have to punt it out another couple weeks.

I'll shoot some video when it finally happens. I've seen posts with youtube clips imbedded in the body of the post...not just a link. How do we do that?

[JonathanL]

You've got to put the vid onto photo bucket or something like that first, then put it in between the video things from "full editor" preview before posting, viola!

[PRY4SNO]

[youtube]Just copy the youtube link between the youtube tags.[/youtube]

[DFrosty]

Am in need of oil pan extension (p/n 034 103 627 or 034 103 627 D) for 7A, 3B, AAN, ADU or ABY if anyone has one available...original 7A motor to my build. This is holding up motor break-in and tune

Has anyone else experienced this when installing with new o-ring gasket? Appears to be too thick as extension original to motor (seen in pics) and a replacement have both broken at exactly same upper left hand corner.

Attachment ( 68586 ) : Oil pan extension_front.JPG


Attachment ( 68594 ) : Oil pan extension_side broken.JPG

[TopherGrace]

Cheapest one by a long shot

https://www.ecstuning.com/Search/SiteSe ... /ES272998/" onclick="window.open(this.href);return false; ... /ES272998/

[DFrosty]

It's finally happening!! Major progress to the point where I'll be bringing her back home!!
:bashtard:

Attachment ( 84097 ) : 90q_dyno day_1.JPG


Attachment ( 84105 ) : 90q_dyno day_2.JPG

[DFrosty]

Finally got her back! Next steps...Bodywork

1st time ever towing a car on a trailer...No less on the hottest day so far of this year 8)

Attachment ( 84313 ) : 90q_tow_1.JPG


Attachment ( 84321 ) : 90q_tow_2.JPG

[DFrosty]

Cleaned up some main harness wiring between block and firewall this past weekend and slipped these slippers on...

Attachment ( 85681 ) : 90q_RS2brakeducts_front_wide.JPG


Attachment ( 85689 ) : 90q_RS2brakeducts_left_front_med.JPG


Attachment ( 85697 ) : 90q_RS2brakeducts_left_cu.JPG

[Twintowers]

Are those gravel guards?


Sent from my iPhone using Tapatalk

[Hybrid_Hatch]

Look like the RS2 air ducts for brakes

[DFrosty]

Look like the RS2 air ducts for brakes

RS2 Brake cooling ducts indeed

[Twintowers]

Wings..lol


Sent from my iPhone using Tapatalk

[DFrosty]

Wings..lol


Sent from my iPhone using Tapatalk

...and that's no Red Bull

[PRY4SNO]

Nice to see you've migrated

I think any of the pics you'd uploaded to MG have to be either hosted elsewhere or hosted here.

[DFrosty]

Nice to see you've migrated

I think any of the pics you'd uploaded to MG have to be either hosted elsewhere or hosted here.

Nice to be here, thank you for having me.

PM reply from Marc says a fix to reference pix is currently in the works.

[DFrosty]

S2 front bumper mock up

[PRY4SNO]

Ohhhhh yeah... that's the stuff.

[DFrosty]

Would any of you have a suggestion for a better solution to this clearance issue between the backside of the right headlight and the Turbo Inlet hose?? Kinda not liking the stress it will put on the headlight connector and the way it forces the light to be aimed down and in.

Thanks

[ringbearer]

Cobra head style hose may help.