HPR Customer Project Car: Driving Video

AngryTaco · Post by **AngryTaco** » Sat Feb 28, 2015 11:31 am

Alright well it's update time since I've been so sparse to even get a hold of recently.

Wagon is at the house and the motor is getting torn down and the short block rebuilt tomorrow. We decided to use the head that came off of my old 20vt with the stainless valves and port work. I'm also going use my hogged out exhaust manifold as the one that came on this motor is 10x worse. He's going to buy a tubular setup from me in the future after I get set up with the TIG.

The machine shop checked out the head after what it went through and they said everything is fine and in good shape.

Now, on to the fun stuff, battery is going to be relocated to the rear like most 20v cars, I'm throwing my already bent tie rod in his car (assuming it's the same as whats on there already), making brackets for the 200 intercooler, and doing a much more cleaner job of fabbing up the bypass valve system.

For now, we are going to stick with stock boost levels and the MC2 cam so as not to anger the CIS gods again (learned my lesson on that one)

DE80q · Post by **DE80q** » Sat Feb 28, 2015 12:26 pm

Nice to see you wrenching on this again. Should be a fun little car when its done.

AngryTaco · Post by **AngryTaco** » Sun Mar 08, 2015 7:37 pm

I have too much shit in the garage lol

DE80q · Post by **DE80q** » Sun Mar 08, 2015 7:40 pm

And the rebuild starts!

AngryTaco · Post by **AngryTaco** » Sun Mar 08, 2015 10:10 pm

I'm just thankful for the weather we've been having. Ultra sunny and 60-degrees. Could not ask for better weather during this time of the year

DE80q · Post by **DE80q** » Sun Mar 08, 2015 10:14 pm

The weather here in PA is finaly supposed to be getting nicer. Will be nice for when I get the bandit back. Then I can install your mounts.

AngryTaco · Post by **AngryTaco** » Sun Mar 08, 2015 10:43 pm

They are on the way!!!!!

AngryTaco · Post by **AngryTaco** » Sat Mar 21, 2015 11:35 am

Getting paint and reassembly this weekend

AngryTaco · Post by **AngryTaco** » Thu Mar 26, 2015 1:50 am

dana · Post by **dana** » Thu Mar 26, 2015 7:00 am

why are you rebuilding this? did it have bad bearings and rings?

ringbearer · Post by **ringbearer** » Thu Mar 26, 2015 9:29 am

I guess you didn't take Gerners advice on honing. Oh well, it's Idaho! Run the crap out of it!

AngryTaco · Post by **AngryTaco** » Thu Mar 26, 2015 10:05 am

dana wrote:why are you rebuilding this? did it have bad bearings and rings?

Customer wanted it rebuilt to begin with. Upon disassembly, one rod bearing needed to be changed regardless as it wouldnt have lasted another 10,000 miles before oil pressure problems

AngryTaco · Post by **AngryTaco** » Thu Mar 26, 2015 10:06 am

ringbearer wrote:I guess you didn't take Gerners advice on honing. Oh well, it's Idaho! Run the crap out of it!

I must have missed that. Didnt realize there was something from him about that. Ive always honed this way and have never had any blowby or excessive oil consumtion.

Edit: just read it. This is going to be a 250ish hp motor when all said and done. When I honed mine before blowing it up I had minimal blowby and oil loss (if any)

AngryTaco · Post by **AngryTaco** » Thu Mar 26, 2015 12:37 pm

[youtube]http://www.youtube.com/watch?v=mMA87-ZPF-4[/youtube]

[youtube]https://www.youtube.com/watch?v=LpTDOo8VP8k[/youtube]

ringbearer · Post by **ringbearer** » Thu Mar 26, 2015 12:39 pm

Can wait to see it eat those pesky 20 valvers!

AngryTaco · Post by **AngryTaco** » Sun Mar 29, 2015 7:36 pm

DE80q · Post by **DE80q** » Sun Mar 29, 2015 7:40 pm

Looks like an engine again!

PRY4SNO · Post by **PRY4SNO** » Mon Mar 30, 2015 12:08 am

WTH were those bearings/balls? I've seen something similar from the coolant passages, from a stop-leak product before... is that it?

85oceanic · Post by **85oceanic** » Mon Mar 30, 2015 12:08 am

Does it run yet?

DE80q · Post by **DE80q** » Mon Mar 30, 2015 5:57 am

PRY4SNO wrote:WTH were those bearings/balls? I've seen something similar from the coolant passages, from a stop-leak product before... is that it?

Under the head studs. Keeps them from bottoming out on the threads.

AngryTaco · Post by **AngryTaco** » Mon Mar 30, 2015 9:18 am

PRY4SNO wrote:WTH were those bearings/balls? I've seen something similar from the coolant passages, from a stop-leak product before... is that it?

1/4" ball bearings. They go under the headstuds as dave said. They keep threads from bottoming out which keeps the studs under compression rather than tensile or torsional forces

PRY4SNO · Post by **PRY4SNO** » Mon Mar 30, 2015 2:00 pm

Coooool

AngryTaco · Post by **AngryTaco** » Tue Apr 14, 2015 8:50 pm

JT gets dropped tomorrow!

AngryTaco · Post by **AngryTaco** » Thu Apr 16, 2015 11:12 pm

5th gear swap complete

AngryTaco · Post by **AngryTaco** » Sat Apr 18, 2015 11:41 am

HPR Customer Project Car: Driving Video

Re: HPR Customer Project Car: VIDEOS AND PICZ!!!!!

Re: HPR Customer Project Car: VIDEOS AND PICZ!!!!!

Re: HPR Customer Project Car: VIDEOS AND PICZ!!!!!

Re: HPR Customer Project Car: VIDEOS AND PICZ!!!!!

Re: HPR Customer Project Car: VIDEOS AND PICZ!!!!!

Re: HPR Customer Project Car: VIDEOS AND PICZ!!!!!

Re: HPR Customer Project Car: VIDEOS AND PICZ!!!!!

Re: HPR Customer Project Car: VIDEOS AND PICZ!!!!!

Re: HPR Customer Project Car: VIDEOS AND PICZ!!!!!

Re: HPR Customer Project Car: VIDEOS AND PICZ!!!!!

Re: HPR Customer Project Car: VIDEOS AND PICZ!!!!!

Re: HPR Customer Project Car: VIDEOS AND PICZ!!!!!

Re: HPR Customer Project Car: VIDEOS AND PICZ!!!!!

Re: HPR Customer Project Car: VIDEOS AND PICZ!!!!!

Re: HPR Customer Project Car: VIDEOS AND PICZ!!!!!

Re: HPR Customer Project Car: VIDEOS AND PICZ!!!!!

Re: HPR Customer Project Car: VIDEOS AND PICZ!!!!!

Re: HPR Customer Project Car: VIDEOS AND PICZ!!!!!

Re: HPR Customer Project Car: VIDEOS AND PICZ!!!!!

Re: HPR Customer Project Car: VIDEOS AND PICZ!!!!!

Re: HPR Customer Project Car: VIDEOS AND PICZ!!!!!

Re: HPR Customer Project Car: VIDEOS AND PICZ!!!!!

Re: HPR Customer Project Car: VIDEOS AND PICZ!!!!!

Re: HPR Customer Project Car: VIDEOS AND PICZ!!!!!

Re: HPR Customer Project Car: UPDATED PICZ!!!!