Ed's 1992 UrS4 "da fridge" - da movie

[highlander69]

Ed,

Feckin impressive........that's all

[EDIGREG]

The AAN one is wider and more substantial. But the distance between the engine and mount is identical.
Also, 20vt motors are not that bad, turbo is much higher along with the exhaust etc.
20vt with stock manifold place the exhaust very low and close to both mount, starter and even the oil filter housing.
Ur-q even came with a funky shield for the starter and motor mount as well as the oil filter housing, to protect them from all that heat.

Cheers
Martin

Thx for the info Martin! Justin is the only one I've seen melt one of these and that was on a 20vt, so that makes sense

ED, with all the power and revs you got, is your motor balanced?..its not mentioned in your specs.

Yes, the motor was balanced by Dave Jones during the rebuild.

Ed,

Feckin impressive........that's all

Thanks Craig!!

[EDIGREG]

Updated to 1.2.9 and got on the dyno again last night... hit fuel cut immediately. I need to sit down and figure out the new boost controller because even when set to use RPM vs DC for the reference lookup, it is overboosting like crazy. Nevermind trying the new boost target based reference lookup (WTF is the Y axis??). Had to take my n75 DC down to 8% to get it under control. It seems like it may be referencing the closed loop boost targets despite the fact that the PID controller is OFF (all set to 0)???




Anyways, it did 560whp/501wtq on the first clean pull that we got, and that was at about .75 lambda. Tried to make some tweaks then BAM.

FAIL



Aaron providing the obligatory finger for me



Duct tape and zip ties to the rescue so I could have SOME boost on the ride home



Time for a wiggens clamp on the compressor outlet and solid piping.

[Hank]

Did the :::WARNING: DANGER TO MANIFOLD::::: light come on and you just ignored it?

[mushasho]

Damn kid... That's some powah!!! That over boosting probably accelerated the process though...

The mods never end at this stage... Sigh

Sent from my HTC One using Tapatalk 2

[themagellan]

Did the :::WARNING: DANGER TO MANIFOLD::::: light come on and you just ignored it?

hahahahah, busting intake welds every damn time.

[EDIGREG]

Damn kid... That's some powah!!! That over boosting probably accelerated the process though...

The mods never end at this stage... Sigh

Sent from my HTC One using Tapatalk 2

Well, fuel cut was set at 340kpa so it didn't exceed that. A 4-ply silicone hose should be able to hold that no problem, it was just a crappy/defective hose I guess. OBX-R brand (it was the 'R' version!! )

I'm gonna get a vanjen clamp for that spot, only $100 for the clamp, yayyy

[EDIGREG]

Did the :::WARNING: DANGER TO MANIFOLD::::: light come on and you just ignored it?

[chaloux]

Hmm, so when are you going to start making some real power?

on my stinking phone!

[Hank]

As if baseline 560whp isn't real power

[WOMBAT]

Lol nicely done!

[loxxrider]

Nice Ed.

That is why I have sworn off silicone and just went to Vanjens, Hargetts (NLA I guess :/) or Wiggens.

[EDIGREG]

Bought a 2.5" vanjen for the compressor outlet. The Hargetts are just as expensive if not more so for the 3-piece clamps. What makes you think they're NLA?

[roortube]

Nice numbers Ed. You still running the SB SSX/JB combo? How's it holding up to this torture?

[EDIGREG]

Yessir, full face "stage 4" (old SB nomenclature) w/ JBR FW. Has not slipped once!

[EDIGREG]

Installed a Vanjen clamp on the compressor outlet and hard pipe to get rid of the silicone, boost is BACK.

These clamps are freaking awesome. Uber high quality components, the flanges have a nice machined lip that mates to the pipe for welding. And I can't believe how much movement they allow...crazy.


naked turbo

[urs6ville]

purdy... very purdy. can't wait to get a ride in da fridge at SFEST.

[glibobbo21]

Damn I should have gotten one of those instead of vband for my hx40....ugh

[85oceanic]

drooooll

[urs6ville]

Yo Ed.. heard you had a tune switching switch with a key lockout... what did you end up with? Thinking it is a good idea for various reasons and was curious... seems like I might be heading down the E85 slope.

[Marc]

Yo Ed.. heard you had a tune switching switch with a key lockout... what did you end up with? Thinking it is a good idea for various reasons and was curious... seems like I might be heading down the E85 slope.

I can order one in for you Dan. let me know when you're ready.

[urs6ville]

I can order one in for you Dan. let me know when you're ready.

Cool... do you have a reference link though... I wanted to see exactly what it was/mounting possibilities/etc

[EDIGREG]

Here is the one I have:

http://www.amazon.com/gp/aw/d/B001TR5BS ... 00_s00_i00

I mounted it next to the LCD screen under the CC head...will snap a pic tomorrow.

[Marc]

sure. like this:

(you can just order this one if you want, or browse ebay for spst key switch (thats the search term I used):



http://www.ebay.com/sch/i.html?_trksid= ... &_from=R40

[EDIGREG]

here's a pic dan. I actually haven't even hooked it up yet since I run E85 all the time....but will need to hook it up for the //sfest road trip.