my VR6T o1e Vems CQ
Re: my VR6T o1e Vems CQ
So what ever happened here? I know you didnt make it to Carlisle. The only CQ there was Jack's.
"If you can't find one, make one"
Dallastown, PA
1991 Audi 80 quattro (20vt project)
1991 Audi Coupe Quattro (project: my first 20v)
2007 Mitsubishi Raider(Dakota in disguise)
2019 Chevy Cruze RS hatch (wife's little red sporty car)
Dallastown, PA
1991 Audi 80 quattro (20vt project)
1991 Audi Coupe Quattro (project: my first 20v)
2007 Mitsubishi Raider(Dakota in disguise)
2019 Chevy Cruze RS hatch (wife's little red sporty car)
Re: my VR6T o1e Vems CQ
...
24v-VR6T-CQ BEAST http://www.theprojectpad.com/viewtopic.php?f=11&t=193#p37887
16v-ABA-T VEMS O1E ETC 4Kq http://www.theprojectpad.com/viewtopic.php?f=11&t=201#p38264
16v-ABA-T VEMS O1E ETC 4Kq http://www.theprojectpad.com/viewtopic.php?f=11&t=201#p38264
-
boost_addict
- Posts: 49
- Joined: Tue Apr 22, 2014 11:55 pm
- Location: N of Philly
Re: my VR6T o1e Vems CQ
no Carlisle. i didn't make it
I eneded up working a deal with a friend of mine. we took my car to his shop and he made me a moly 1 piece shaft. I still have to make him a vems harness and tune his shit for life.. but I like to make cars faster. especially on their Dime..
car is running but only on baseline wg, ~18 psi or so. on pump gas. i drove it maybe 10 times so far, but its mostly all been break in and tuning.
1 rear oem tie rod came apart on me. so i need to make these moly rear ties already.. i have had material to make them for over a year now.. so serves me right.
also need to finish exhaust and get it past the rear subframe/axles and out the rear end.
i plan on getting some time in the garage this weekend. im going to try to finish the rear tie rods then i plan to turn the boost up and see how sideways she will go.
exhaust is quiet enough for now. it sounds mean open dp and short muffler dump under the car..
I eneded up working a deal with a friend of mine. we took my car to his shop and he made me a moly 1 piece shaft. I still have to make him a vems harness and tune his shit for life.. but I like to make cars faster. especially on their Dime..
car is running but only on baseline wg, ~18 psi or so. on pump gas. i drove it maybe 10 times so far, but its mostly all been break in and tuning.
1 rear oem tie rod came apart on me. so i need to make these moly rear ties already.. i have had material to make them for over a year now.. so serves me right.
also need to finish exhaust and get it past the rear subframe/axles and out the rear end.
i plan on getting some time in the garage this weekend. im going to try to finish the rear tie rods then i plan to turn the boost up and see how sideways she will go.
exhaust is quiet enough for now. it sounds mean open dp and short muffler dump under the car..
91 VEMS CQ vr6 6766 o1e s2.
01 GTI vr6 vems 6262
01 2500 Cummins hx40. Tow Rig, vems round 80psi
01 GTI vr6 vems 6262
01 2500 Cummins hx40. Tow Rig, vems round 80psi
-
boost_addict
- Posts: 49
- Joined: Tue Apr 22, 2014 11:55 pm
- Location: N of Philly
Re: my VR6T o1e Vems CQ
something like this. i gotta get pics of mine in the car. i forgot to when it was on his lift getting done..
im also running 10.5:1 compression and holy shit does it spool quick.

im also running 10.5:1 compression and holy shit does it spool quick.

91 VEMS CQ vr6 6766 o1e s2.
01 GTI vr6 vems 6262
01 2500 Cummins hx40. Tow Rig, vems round 80psi
01 GTI vr6 vems 6262
01 2500 Cummins hx40. Tow Rig, vems round 80psi
- speeding-g60
- Posts: 2152
- Joined: Fri Mar 01, 2013 10:46 am
Re: my VR6T o1e Vems CQ
you need a dogbox......
-
boost_addict
- Posts: 49
- Joined: Tue Apr 22, 2014 11:55 pm
- Location: N of Philly
Re: my VR6T o1e Vems CQ
I need your old dogbox. you build enough cars you should sponsor too hehe..
I need one bad. but I have less into the setup + buying the car stock then I would spend on a trans.
my time is free to me and it was all made and built in my garage. I still have some things to finish but the dogbox blows my budget build out of the water. but I agree with you aaron.
speaking of water, I just went and looked at a 30' Baja outlaw on fathers day.. so I guess that's the real reason I haven't pulled the trigger on yours YET... The summer is too hot for me so I need a boat again. but if I don't find what I am looking for come aug/sept/ h20i time, that will change.
every year around this time i wish i never sold my old Baja and instead turbod that. so i have been dicking around with the coupe a lot.
this weekend i will get some time out there again. the old lady has been bitching this week so i need to blast away a couple gears badly
I need one bad. but I have less into the setup + buying the car stock then I would spend on a trans.
my time is free to me and it was all made and built in my garage. I still have some things to finish but the dogbox blows my budget build out of the water. but I agree with you aaron.
speaking of water, I just went and looked at a 30' Baja outlaw on fathers day.. so I guess that's the real reason I haven't pulled the trigger on yours YET... The summer is too hot for me so I need a boat again. but if I don't find what I am looking for come aug/sept/ h20i time, that will change.
every year around this time i wish i never sold my old Baja and instead turbod that. so i have been dicking around with the coupe a lot.
this weekend i will get some time out there again. the old lady has been bitching this week so i need to blast away a couple gears badly
91 VEMS CQ vr6 6766 o1e s2.
01 GTI vr6 vems 6262
01 2500 Cummins hx40. Tow Rig, vems round 80psi
01 GTI vr6 vems 6262
01 2500 Cummins hx40. Tow Rig, vems round 80psi
Re: my VR6T o1e Vems CQ
still no sideways action :(
24v-VR6T-CQ BEAST http://www.theprojectpad.com/viewtopic.php?f=11&t=193#p37887
16v-ABA-T VEMS O1E ETC 4Kq http://www.theprojectpad.com/viewtopic.php?f=11&t=201#p38264
16v-ABA-T VEMS O1E ETC 4Kq http://www.theprojectpad.com/viewtopic.php?f=11&t=201#p38264
Re: my VR6T o1e Vems CQ
...
24v-VR6T-CQ BEAST http://www.theprojectpad.com/viewtopic.php?f=11&t=193#p37887
16v-ABA-T VEMS O1E ETC 4Kq http://www.theprojectpad.com/viewtopic.php?f=11&t=201#p38264
16v-ABA-T VEMS O1E ETC 4Kq http://www.theprojectpad.com/viewtopic.php?f=11&t=201#p38264