Page 61 of 82
Re: Nick's 1991 200q Project - QUAT44RO
Posted: Thu Mar 06, 2014 6:04 pm
by themagellan
Either route is amazing power.... Let's not forget Nick is already 1-0 against the mighty 07k..... We haven't seen his final form (Queue Dragonball Z music)
[youtube]http://www.youtube.com/watch?v=vld88zccDvw[/youtube]
Re: Nick's 1991 200q Project - QUAT44RO
Posted: Fri Mar 07, 2014 2:19 am
by amd is the best
Someone with knowledge on the subject... RS2 intake manifold or not worth it? GO!
Re: Nick's 1991 200q Project - QUAT44RO
Posted: Fri Mar 07, 2014 2:41 am
by Mcstiff
amd is the best wrote:Someone with knowledge on the subject... RS2 intake manifold or not worth it? GO!
JShadzi wrote:Ok...flow #'s for the 3B...honestly, I was surprised at how bad it actually was. My hypotesis is that flow would degrade further from the inlet, and it was right on...
Total variation of over 12% and 9% from average, #1 cylinder really getting the shaft. Now on average a stock head flows about 200cfm, so the net effect may or may not be so bad. I made over 500whp with this manifold, but I never measured cyl-to-cyl performance, its comforting to see that the manifold I"m now running flows MUCH more consistently from cyl-to-cyl and flows significantly more overall.
FWIW, my new big valve head will outflow even the #5 cylinder of a 3B manifold 8)
JShadzi wrote:OK kids...here ya go.
I'll preface by saying I didn't believe it myself either, but the #'s don't lie. Same flowbench, same procedure as the previous 2. We even went back and ran it again to verify, same exact results...
About 5% less flow across the board than the 3B we tested, make your own conclusions
Take it as you will, lots of bickering about how to flow a manifold here
http://www.motorgeek.com/viewtopic.php?t=9764
Re: Nick's 1991 200q Project - QUAT44RO
Posted: Fri Mar 07, 2014 6:06 am
by chaloux
Take the guide shafts out.
Re: Nick's 1991 200q Project - QUAT44RO
Posted: Sat Mar 08, 2014 11:40 am
by PRY4SNO
Any updates on your fuel pump solution, or still waiting on the 3d printer?
Re: Nick's 1991 200q Project - QUAT44RO
Posted: Mon Mar 10, 2014 10:17 pm
by amd is the best
PRY4SNO wrote:Any updates on your fuel pump solution, or still waiting on the 3d printer?
I've got a few printed but I'm not going to install the pumps for a while. I want the new engine to run on the old fuel system for break in so it'll be a but until I know how the double pump setup works out.
Small update, my block now takes the record for most rusty block Jeff has ever seen. After it came out of the hot tank:
After shot blasting:
Journals:
Re: Nick's 1991 200q Project - QUAT44RO
Posted: Mon Mar 10, 2014 10:28 pm
by chaloux
Well that's quite the transformation! Looks good Nick, can't freaking wait for vids.
Re: Nick's 1991 200q Project - QUAT44RO
Posted: Mon Mar 10, 2014 10:33 pm
by amd is the best
There will be vids-o-plenty. Testing out the Magic Lantern firmware for my Canon's. Should help make the footage a bit higher quality.
Re: Nick's 1991 200q Project - QUAT44RO
Posted: Mon Mar 10, 2014 10:46 pm
by chaloux
amd is the best wrote:There will be vids-o-plenty. Testing out the Magic Lantern firmware for my Canon's. Should help make the footage a bit higher quality.
I've thought about that firmware, but never really looked into it too much. Or when I was it was write a while ago. I'd love a higher fps setting for the 5d2. I think I will check it out... I need to make something with the 4k too.
Re: Nick's 1991 200q Project - QUAT44RO
Posted: Mon Mar 10, 2014 10:56 pm
by amd is the best
chaloux wrote:amd is the best wrote:There will be vids-o-plenty. Testing out the Magic Lantern firmware for my Canon's. Should help make the footage a bit higher quality.
I've thought about that firmware, but never really looked into it too much. Or when I was it was write a while ago. I'd love a higher fps setting for the 5d2. I think I will check it out... I need to make something with the 4k too.
Even with ML, I think the 5D2 is limited to 24 or 30fps. My 7D will do 60 but only at 720p which is fine for some slow motion footage.
ML gives some real cool control over audio and tons of other neat tricks.
Re: Nick's 1991 200q Project - QUAT44RO
Posted: Wed Mar 12, 2014 11:19 am
by loxxrider
In reference to your fb/ig query, here is my car with the fading rings... I think they look pretty good.
Re: Nick's 1991 200q Project - QUAT44RO
Posted: Wed Mar 12, 2014 12:41 pm
by amd is the best
Do they fade to white or clear?
Re: Nick's 1991 200q Project - QUAT44RO
Posted: Wed Mar 12, 2014 2:57 pm
by loxxrider
amd is the best wrote:Do they fade to white or clear?
Clear because its a dot matrix.
Re: Nick's 1991 200q Project - QUAT44RO
Posted: Wed Mar 12, 2014 5:58 pm
by amd is the best
Re: Nick's 1991 200q Project - QUAT44RO
Posted: Wed Mar 12, 2014 6:30 pm
by gtn116
Quality photobomb, btw.
Re: Nick's 1991 200q Project - QUAT44RO
Posted: Wed Mar 12, 2014 9:20 pm
by 2.5TYPE44
Looking good. Man, I sure would like to have one of those. Project is moving along! Can't wait to get feedback.
Re: Nick's 1991 200q Project - QUAT44RO
Posted: Thu Mar 13, 2014 7:28 am
by loxxrider
Lol I bet she loves the car parts in the house. When they're that nice, why not?!
Re: Nick's 1991 200q Project - QUAT44RO
Posted: Wed Mar 19, 2014 9:05 pm
by amd is the best
To re-iterate, the main stud kit offered by ARP specific to our 2.2-2.3 20v engines is incorrect. Kit 204-5404.
Re: Nick's 1991 200q Project - QUAT44RO
Posted: Thu Mar 20, 2014 10:27 am
by 85oceanic
Want.
Re: Nick's 1991 200q Project - QUAT44RO
Posted: Thu Mar 20, 2014 7:16 pm
by amd is the best
BE JELLY:
Re: Nick's 1991 200q Project - QUAT44RO
Posted: Thu Mar 20, 2014 7:23 pm
by loxxrider
so cool
Re: Nick's 1991 200q Project - QUAT44RO
Posted: Thu Mar 20, 2014 7:31 pm
by chaloux
Nice. Epic styles
Re: Nick's 1991 200q Project - QUAT44RO
Posted: Thu Mar 20, 2014 7:34 pm
by amd is the best
Not sure if I want to put them on the wagon or not yet.
Re: Nick's 1991 200q Project - QUAT44RO
Posted: Thu Mar 20, 2014 10:06 pm
by vt10vt
I love the look of them on your sedan. I'm thinking of going with a faux rally car look for the 5k, (tastefully) large mud flaps, a couple hellas in front of the grille, flat black hood w/ leather strap and a big 'ol obnoxious reverse fog
Re: Nick's 1991 200q Project - QUAT44RO
Posted: Fri Mar 21, 2014 7:46 am
by CassaUrS6
Stupid ass mud flaps.. smh
